| Version 15.7/25.7 |
|
Date: 11/2/00 |
New Features: Time marker settings based on TMP2 board are now saved with the mode file.
Corrections: None.
Notes: None.
| Version 15.6/25.6 |
|
Date: None |
New Features: None.
Corrections: None.
Notes: Not officially released.
| Version 15.5/25.5 |
|
Date: 12/14/99 |
New Features: None.
Corrections: Improved the hard drive status for SCP1 data capture.
Notes: None.
| Version 15.4/25.4 |
|
Date: 4/12/99 |
New Features: None
Corrections: Enhanced autorange. Event-based grids disabled when no TMP2 is present.
Notes: SCP1B firmware V 1.8 improves SCSI data capture lockup when aborting.
| Version 15.3/25.3 |
|
Date: 9/25/98 |
New Features: Removes the test for GPIB functionality on boot up.
Corrections: None.
Notes: Because the GPIB chip has been discontinued, new K2 recorders won't have the GPIB chip installed unless specifically requested.
| Version 15.2/25.2 |
|
Date: 9/21/98 |
New Features: Enhances Quick Range to improve the ability to calibrate to non-zero values.
Corrections: DOS file date created when saving files to the floppy disk for years set to 2000 or higher.
Notes: None.
| Version 15.1/25.1 |
|
Date: 6/16/98 |
New Features: Provides additional derived timing markers for the TMP2.
Corrections: None
Notes: Requires TMP2 firmware v1.2.
| Version 15.0/25.0 |
|
Date: 4/29/98 |
New Features: For the TMP2, adds the ability to control four event markers which can toggle at different time rates.
Corrections: None
Notes: Requires EPROM changes to both printhead control boards as well as TMP2 firmware v1.1
| Version 14.9/24.9 |
|
Date: 3/17/98 |
New Features: Adds Quick Range feature, which allows a user to calibrate the amplifiers to an external source.
Corrections: None
Notes: Version 14.8 never officially released due to a bug problem with Standard Recorder mode.
| Version 14.7/24.7 |
|
Date: 5/29/97 |
New Features: None
Corrections: Modified the on-demand buffer printing.
Notes: None
| Version 14.6/24.6 |
|
Date: 4/17/97 |
New Features: None
Corrections: Enhances host lock-out during data archive.
Notes: None
| Version 14.5/24.5 |
|
Date: 1/31/97 |
New Features: Adds motor speed calibration compensation, allows user to adjust speed +/- 2%.
Corrections: None
Notes: None
| Version 14.4/24.4 |
|
Date: 12/31/96 |
New Features: Adds alarm color for VOP-3, waveform will change color based on user-defined limits.
Corrections: Modifies data capture for captures with roll over from one month to another.
Notes: None
| Version 14.3/24.3 |
|
Date: 10/16/96 |
New Features: None
Corrections: Modified on-demand buffer action. Improved IRIG time decoding.
Notes: None
| Version 14.2/24.2 |
|
Date: 9/6/96 |
New Features: Adds support for new revision DWP2 board with synchronous recording. Auto ID now prints immediately when starting a capture playback. Adds new DWP2 host commands.
Corrections: Modifies mode upload via RS232. Improves DWP2 communication.
Notes: None
| Version 14.1/24.1 |
|
Date: 1/3/96 |
New Features: Adds support for SCP1 sample rates of 1,2 and 5 Hz. Adds utility to calculate absolute playback time in terms of date and time. Display labels can now be displayed during data capture. Adds LOAD/LOAD+RUN choice when loading a mode from disk. Adds clock trigger source.
Corrections: None
Notes: SCP1 firmware upgrade required for this version of K2 system software. Version 14.0 was not released.
| Version 13.9/23.9 |
|
Date: 10/23/95 |
New Features: Adds data capture time stamp to record select menu in data playback mode. Adds a COPY command to the zero/gain menus.
Corrections: Improves the ARCW host command for data captures larger than 512K.
Notes: None
| Version 13.8/23.8 |
|
Date: 8/30/95 |
New Features: None
Corrections: Improves the bridge type selection for the AWP4.
Notes: None
| Version 13.7/23.7 |
|
Date: 6/15/95 |
New Features: None
Corrections: Improves signal conditioner reporting for AWP2 and AWP2-40 after auto-calibration.
Notes: None
| Version 13.6/23.6 |
|
Date: 5/25/95 |
New Features: None
Corrections: Improves the CLHS host command.
Notes: Version 13.5 was not released
| Version 13.4/23.4 |
|
Date: 2/14/95 |
New Features: None
Corrections: Enhances range settings for modes downloaded via host control.
Notes: None
| Version 13.3/23.3 |
|
Date: 1/9/95 |
New Features: Added new CLHS command, allowing the host to clear the halted flag generated by the CHRT 0 command.
Corrections: None
Notes: This was added for a specific application at Boeing
| Version 13.2/23.2 |
|
Date: 10/8/94 |
New Features: Adds user scaling to the zero/gain menus. Enhances the operation of the external keyboard input from the VOP1 board. Adds support for the new AWP1 board (optical isolation).
Corrections: Coordinates the playback window command for both SCP1 and DCP1 boards.
Notes: None
| Version 13.1/23.1 |
|
Date: 7/1/94 |
New Features: Adds mode upload/download feature via host control.
Corrections: None
Notes: None
| Version 13.0/23.0 |
|
Date: 5/12/94 |
New Features: Adds scaling feature for DWP1 via front panel and host control.
Corrections: None
Notes: None
| Version 12.9/22.9 |
|
Date: 3/17/94 |
New Features: Adds support for DSP2 digital signal processing module
Corrections: None
Notes: Necessary upgrade for DSP2 board.
| Version 12.8/22.8 |
|
Date: 3/17/94 |
New Features: Adds auto-archive capability, data stored on a DCP1 can be archived to an SCP1. Adds two mean filters for the AWP4.
Corrections: Enhances signal conditioner reporting when using zero suppression with an AWP1. Increases the reliability of RS232 interface. Enhances the system event marker archive and upload.
Notes: Requires new AWP4 firmware for mean filtering.
| Version 12.7/22.7 |
|
Date: 12/20/93 |
New Features: Adds AUTORANGE ALL feature. Adds FFT ZOOM feature. Adds numeric playback as a choice for playback settings. Adds auto-stacked parallel capture (data can now be stored on the DCP1 and SCP1 simultaneously). Adds signal conditioner reporting for AWP4. Adds the ability to arm a capture via the utility port. Adds support for new motor power tables.
Corrections: Improves XON/XOFF handshaking.
Notes: Requires EPROM update for SSB board, as well as new motor wiring harness (IMPORTANT).
| Version 12.6/22.6 |
|
Date: 8/20/93 |
New Features: Adds support for the AWP4 dc-bridge module. Adds the analog settings to data captured on DCP1 and SCP1 boards. Adds a "stuck-key" check on power-on. Dashes are now displayed for time on playbacks with external sample rate.
Corrections: Improves data playback time code (IRIG) resolution. Enhances event marker enable via host control.
Notes: VOP1 and TMP1 firmware upgrades released. Version 12.5 was not released.
| Version 12.4/22.4 |
|
Date: 4/15/93 |
New Features: Adds support for two TGP1 boards, a total of 16 channels of triggering. Adds VOP1 screen dump feature. Adds support for playback sample numbers for VOP1. Adds GROUND ALL/UNGROUND ALL feature under the zero/gain menu. Adds enhanced signal conditioner reporting - left and right grid values. Adds support for zero position accuracy to 1/10th of 1 percent. Adds support for enable/disable DWP1 system event driver.
Corrections: Improved data playback from SCP1 to VOP1. Enhances host control commands such as TSRC, CHAN?, GRSY, and GRMN.
Notes: VOP1 requires v1.3 firmware upgrade.
| Version 12.3/22.3 |
|
Date: 3/25/93 |
New Features: Adds trigger setting to general help sheet. The VOP1 can now be set to a different chart than the paper output. Adds two new time mark selections - 3.6 and 6 seconds. Adds new host control commands for VOP1 support. Soft key #10 now operates as a LOCAL key when display labels are on.
Corrections: Slew rate triggering is allowed when window triggering is disabled on power-up. The VOP1 now operates correctly when installed in slot 9 with no other peripherals enabled. An asterisk (*) is not allowed in the file names on the floppy drive.
Notes: VOP1 requires v1.2 firmware upgrades released..
| Version 12.2/22.2 |
|
Date: 2/10/93 |
New Features: Support for new SCP1A board, with DAT backup feature. Adds time and date to the calibration report. The TMP1 has been enhanced with more accurate end-of-capture time stamp.
Corrections: Improved host download after power-up. Zero position on the channel status report prints correctly. Improved the ARMC? host control command.
Notes: SYSCON, SCP1 and VOP1 firmware upgrades released.
| Version 12.1/22.1 |
|
Date: 1/20/93 |
New Features: Adds password security feature. Adds support for SCP1 external sample rate.
Corrections: Event marker positions can now be set from host control. Slot enabling for DI488 and AWP1 boards.
Notes: SYSCON and SCP1 firmware upgrades released.
| Version 12.0/22.0 |
|
Date: 12/31/92 |
New Features: Adds darker printing for text and timing marks at various speeds. Adds FFT analysis feature. Adds full page mark for system event. Adds trace thickness control. Adds slot enable/disable feature. Adds plotter mode for host control, can also work with files from floppy disk (using K2 specific format).
Corrections: None
Notes: SCP1 and VOP1 firmware upgrades released.
| Version 11.9/21.9 |
|
Date: 11/25/92 |
New Features: Adds support for SCP1 board.
Corrections: Improves speed change sequences. The data analysis menu now indicates when no data capture board is installed. Enhnaces event marker captures immediately after power-up. Augments data capture from DCP2. Improves data upload via host control.
Notes: Master TPH, SCP1, and VOP1 firmware upgrades released.
| Version 11.8/21.8 |
|
Date: 11/10/92 |
New Features: Adds the Data Analysis (Record Report) feature. Adds support for data capture record upload to host. Adds Capture Duration calculator feature.
Corrections: Improves abort key function during Auto Range. Enhances host control with AWP3.
Notes: Master TPH and VOP1, and DCP2 firmware upgrades released. Version 11.7 not released.
| Version 11.6/21.6 |
|
Date: 9/30/92 |
New Features: Adds support for DI488 peripheral. Adds support for AWP2-40 analog input board. Adds VGA support for VOP1 board. Support for IDP1 peripheral (specific Boeing application). Adds calibration report. Adds Auto Range feature. Various host control enhancements.
Corrections: None
Notes: Master TPH and VOP1 firmware upgrades released.
| Versions 11.0 through 11.5 |
|
Date: N/A |
Notes: These are the original releases for the MT95K2 from April 1992 through September 1992. For further information, contact technical support.
|
|
© 2008 Astro-Med, Inc. All Rights Reserved.
|
